LED street lights are currently one of the key implementation methods to save energy and reduce carbon, all countries in the world have been in full swing to replace the original traditional street lights with LED street lights, and the new street is directly limited to the use of LED street lights to save energy. At present, the world LED street lamp market is about 80 million, the light source of LED lamps, whether it is heat, service life, output spectrum, output illuminance, material characteristics, are different from traditional mercury lamps or high-pressure sodium lamps. The test conditions and test methods are different from traditional lamps, Lab Companion will collect the reliability test methods related to LED street lights and provide everyone with reference. Hope to be able to help and understand for everyone in the introduction of LED related tests.
LED street lamp test specification abbreviation finishing:
LED street lamp test standard specification, LED street lamp test method technical specification, LED street lamp standard and test method, night landscape engineering semiconductor lighting device components product technical specification, semiconductor lighting night landscape engineering construction quality acceptance technical specification, IEC 61347LED power supply safety regulation
LED street lamp test specification conditions:
CJJ45-2006 Urban road lighting design standard, UL1598 lamps safety standard, UL48 wire and cable safety standard, UL8750 light-emitting diode safety standard, CNS13089 light-emitting diode large lamp durability Test - pre-burning test - outdoor, Waterproof Test: IP65, American Standard for LED lamps, EN 60598-1, EN 60598-2 Street lamp test
LED large lamp quality certification test project:
Temperature cycle, temperature and humidity cycle, high temperature preservation, moisture resistance, vibration, shock, continuous power, salt water spray, acceleration, solder heat resistance, solder adhesion, terminal strength, natural drop, dust test
LED large lamp quality certification test conditions finishing:
Temperature cycle: 125℃(30min)←R.T.(5min)→-65℃(30min)/5cycle
LED street lamp (light-emitting diode outdoor display with large lights) failure determination:
a. The axis light is lower than the residual rating of 50%
b. Forward voltage is greater than 20% of the rated value
c. Reverse current greater than 100% of the rated value
d. The half height wave length and half power Angle of the light exceed the limited maximum value or the limited minimum value meet the above conditions, and determine the failure of the LED street lamp
Note: The luminous efficiency of LED street lamp is recommended to be at least 45lm/W or above (the luminous efficiency of LED light source must be about 70 ~ 80lm/W)
High temperature storage: maximum storage temperature 1000 hours [special level 3000 hours]
Moisture resistance: 60℃/90%R.H./1000 hours [characteristic level 2000 hours]/ applying bias
Brine spray: 35℃/ concentration 5%/18 hours [24 hours special level]
Continuous power: maximum forward current 1000 hours
Natural fall: Fall height 75cm/ fall times 3 times/fall material smooth maple wood
Dust test: continuous 360 hours of 50℃ ring temperature test
Vibration: 100 ~ 2000Hz, 196m/s^2, 48 hours
Impact: Grade F[Acceleration 14700m/s^2, pulse amplitude 0.5ms, six directions, three times in each direction]
Equal acceleration: Acceleration is applied in all directions (class D: 196000 m/s^2) for 1 minute
Solder heat resistance: 260℃/10 seconds /1 time
Solder adhesion: 250℃/5 seconds
Terminal strength
LED large lamp batch quality test project:
Terminal strength, solder heat resistance, temperature cycle, moisture resistance, continuous power, high temperature storage
LED large lamp batch quality test conditions:
Moisture resistance: 60℃/90%R.H./168 hours (no failure)/500 hours (one failure allowed)[test number 10 / apply bias]
Continuous power on: maximum forward current /168 hours (no failure)/500 hours (one failure allowed)[test number 10]
High temperature storage: maximum storage temperature /168 hours (no failure)500 hours (one failure allowed)[test number 10]
Solder heat resistance: 260℃/10 seconds /1 time
Solder adhesion: 250℃/5 seconds
LED large lamp regular quality test project:
Vibration, shock, acceleration, moisture resistance, continuous power, high temperature preservation
Regular quality test conditions for LED large lights:
Moisture resistance: 60℃/90%R.H./1000 hours
Continuous power: maximum forward current /1000 hours
High temperature storage: Maximum storage temperature /1000 hours
Vibration: 100 ~ 2000Hz, 196m/s^2, 48 hours
Impact: Grade F[Acceleration 14700m/s^2, pulse amplitude 0.5ms, six directions, three times in each direction]
Equal acceleration: Acceleration is applied in all directions (class D: 196000 m/s^2) for 1 minute
LED large lamp screening test project:
Acceleration test, temperature cycle, high temperature preservation, pre-burning test
LED large light screening test conditions sorting:
Constant acceleration test: Apply acceleration (grade D: 196000 m/s^2) in each direction for 1 minute
Temperature cycle: 85℃(30min)←R.T.(5min)→-40℃(30min)/5cycle
Pre-firing test: temperature (maximum rated temperature)/ current (maximum rated forward current)96 hours
High temperature storage: 85℃/72 ~ 1000 hours
LED lamp life test:
More than 1000 hours of Life Test (Life Test), light attenuation < 3% [withered light]
More than 15,000 hours of Life Test (Life Test), light attenuation < 8%
